News
Birch Powder Extract 10:1 (Betula Alba): Flavonoids as an Antioxidant Lead Marker in the Spray-Dried Powder
Birch (INCI: Betula Alba) is one of the characteristic tree species of the northern climate zones. For formulators in cosmetics and food technology, CONIUNCTA® supplies Birch Powder Extract as a spray-dried concentrate with an extract ratio of 10:1. The fine, golden-yellow to light brown powder concentrates the plant's own compound classes in dispersible form and is suitable as a raw material for water-based and functional applications. This article reviews the documented markers, the activity profile according to the data sheet and the key processing parameters for product development. Why the powder form: 10:1 concentration and processing Birch Powder Extract is produced by spray-drying an extract obtained with water and ethanol; the residual solvents used are removed during the drying process and comply with Directive 2009/32/EC. The result is a characteristic fine powder with a density of 0.50 to 0.70. Compared with liquid carrier variants, a powder extract offers high concentration without carried-over solvent as well as flexibility in formulation architecture, for example in aqueous systems in which it is dispersible. Solubility depends on the extract; technical testing in the target system is therefore part of the development work. For handling purposes, the material is not classified as hazardous under Regulation (EC) No 1272/2008 (CLP) and carries neither a hazard pictogram nor a signal word. When processing powders, eye protection is recommended and aerosols should not be inhaled. According to the safety data sheet, skin protection is not required. Flavonoids as lead marker: the documented analytics The primary marker of Birch Powder Extract is total flavonoids, calculated as hyperoside. According to the CDS, the literature content in the dried plant is 1.5 to 3.5 %; with the concentration factor of 10:1 and a recovery of 70 to 90 %, this results in an indicative product content of 105 to 315 mg/g. The calculation basis relies on Ph. Eur. and ESCOP as pharmacopoeial and peer-reviewed data sources respectively. In addition to the flavonoids, the data sheet documents further characteristic compounds: betulin, a bark-specific triterpene (3 to 5 % in the bark), and chlorogenic acid at 0.3 to 0.8 %. Flavonoids and tannins are named as the defining compound classes. This combination determines the analytical profile of the extract and serves formulators as guidance for batch evaluation based on the certificates of analysis. Documented activity profile within the scope of the markers The CDS assigns defined effects to the compound classes. The flavonoids are described as having antioxidant and UV-protective properties, the tannins as having astringent and antimicrobial properties. The cosmetic effect listed in the CDS is “Antioxidant, capillary strengthening”. A mechanistic background mentioned in the CDS (ROS scavenging, MMP inhibition, NF-κB) is explicitly marked as “not a product claim” and is therefore not a product-related efficacy claim but merely literature-based context. Important for regulatory classification: the CDS explicitly states that no cosmetic claim areas have been derived for this raw material. Formulators should therefore align the promotion of the finished product closely with substantiated statements. Marketing keywords such as “scalp strengthening” or “hair care” are not CDS-verified and do not replace documented efficacy. For food applications, the extract is described as a “traditional dietary ingredient”. Use concentrations and fields of application For cosmetic formulations, the data sheet specifies a use concentration of 2 to 5 %. For orientation: at 3.5 % extract use, this yields a calculated 3.7 to 11.0 mg/g flavonoids in the formulation. For functional foods and beverages, a range of 0.5 to 2 % is given; at 1.3 % extract use, this corresponds to 1.3 to 3.9 mg/g flavonoids in the finished application. These values are calculation examples from the CDS and not formulation recommendations. Our technical team will address specific dosage and formulation questions individually. According to the data sheet, the powder is suitable for all variants in cosmetics and food and is vegan. Regulatory suitability is given for cosmetics in accordance with Regulation (EC) No 1223/2009 and for food, whereby the safety assessment of the finished product lies with the responsible person and allergen labelling under Regulation (EU) No 1169/2011 lies with the food business operator. Fragrance allergens according to Annex III cannot be derived for this raw material, as their retention through the drying process is not documented. Storage, shelf life and stability When stored dry between 10 and 30 °C in the original sealed container, protected from light and moisture, the shelf life is 24 months. The safety data sheet recommends a storage temperature of 15 to 25 °C and keeping containers tightly closed; the material is classified in storage class 11 (combustible solids) according to TRGS 510. Colour changes during storage cannot be ruled out depending on temperature and duration and are typical for botanical powder extracts. The material is delivered in bags in drums. Documentation and sourcing for formulators All parameters mentioned here come from the accompanying product dossier. We provide technical data sheets, safety data sheets and composition data sheets via our technical documentation. Birch Powder Extract is part of our range of classic plant extracts; it is Made in Germany, based among other things on our AVE technology. Our technical team is available for sampling and for integration into your formulation architecture: View Birch Powder Extract 10:1 (Betula Alba) in the CONIUNCTA® shop. CONIUNCTA®: raw materials, data and services for future-proof formulations.
Read more
